A “CAM sensor error” is what Canon Printer Error 6C10 is. But why is there an error in the printer? When the user presses the ON button on the printer, an error message appears, and the green light flashes. After a while, both buttons flash alternately. Most users must reinstall the printer drivers or remove them entirely from the printer to correct this error. Canon printers, without a doubt, provide good performance; they have advanced features and are built by professionals using cutting-edge technology. A printer can now be used for various purposes, eliminating the need for the user to visit a printing shop. They can make professional-looking prints at home, scan images and documents, and make as many duplex copies as possible. They are also able to fax documents.
However, errors in Canon printers can cause them to fail to function. Users may become irritated as a result. However, it would help if you were not concerned because this blog will teach you how to resolve the 6C10 error on a Canon printer.
Simple Steps to Resolve Canon Printer Error 6C10
Step 1
- Place the printhead in the center.
- Check the right side to see if the purge unit is in good working order after disconnecting the printer.
- There should be no paper on the table.
Step 2
- Install your printer again.
- Turn off the power and wait a few moments.
- Turn on the printer now.
- While holding the resume button, hold it for 15 to 20 seconds.
Step 3
- Turn off your Canon printer.
- Now, please open the door.
- Turn your device on.
- Close the door once you’ve determined that the cartridges are in the center.
Step 4
- You can allow your ink cartridge carrier to center itself by opening the lid.
- A row of white rollers can be seen behind the carrier on the right-hand side.
- At the end of the rollers, you’ll notice a small, clear piece of plastic sticking up.
- Now, using a small towel, gently wipe away all of the ink.
- Don’t forget to bring a cotton cloth or a paper towel.
- Proceed to the ink pad section after cleaning the rollers.
- From that piece of plastic, a small square will be visible about 1 or 2 inches in the printer’s direction. A small form pad is located about half an inch away on each side.
- This is where you’ll notice the excess ink accumulating. It is now necessary for you to soak it.
- Place a second paper towel on top of the foam. Repeat until the paper towel is completely saturated with ink.
- Close the lid, turn the printer off, and then back on.
Step 5
Following that, you must clean your Canon printer’s printhead. You can get help from your Canon printer’s manual for this. Read the manual’s guide and follow the step-by-step instructions.
Step 6
- Remove the casing and look for any micro switches that may have been pressed by one of the purge unit cams.
- Your responsibility now is to clean it.
The Counter on the Ink Absorber Must Be Reset
- Turn the printer off.
- Then press and hold the resume button for a few minutes.
- Holding the power button at the same time is the next step.
- This will activate the green LED light.
- Hold the power button while you release the resume button.
- Press and hold the Resume button twice, then release both buttons.
- Now, press the resume button four times, followed by the power button.
The ink absorber counter will be reset by pressing and releasing the power and resume buttons on the printer. Then, please turn off the printer, unplug it, plug it back in, and turn it on. Finally, examine the printer to see if it has recovered from the 6C10 error.
Conclusion
The whole thing is done, so look at your printer when it is done. If it prints well, then the problem has been solved. There’s still a problem with it if it doesn’t print or doesn’t let you print. It needs to be fixed, though.
In this case, you might want to reach out to the experts and ask for their help. All of the people at Canon are well-trained and have a lot of experience, so they can help you. If you call them and tell them what you’re having, they’ll answer all of your questions. It doesn’t matter what kind of problem you have with your Canon printer. They are just a phone call away and will help you.